Mikro ACM® Air Classifying Mills were invented by HMPS in the late 1960’s and are one of the most versatile types of size reduction equipment available in the market. These units while being capable of producing fine, medium and coarse grinds for a wide variety of materials for Food, Pharmaceutical, Chemical and Mineral industries, require very little maintenance over their life span. The basic design of these mills is the impact size reduction that is coupled with an internal dynamic classifier which controls the outlet (product) particle size via recirculating the coarse particles back into the grinding zone.
There are seven main factors which determine particle size distribution for the Mikro ACM® Air Classifying Mill. When varied, the rotor type and speed combined with the liner and hammer count affects the production of fines. The separator type and speed affects the top size of the product. And lastly, the airflow governs the throughput as well as top size and fines generation. With the endless available options a machine can be configured to process just about any material that is below MOH’s hardness of 5.
The Alpine UPZ Ultraplex Fine Impact Mill are truly flexible. Designed with ultimate versatility in mind, this one unit can accomplish a multitude of size reduction tasks. A wide variety of grinding inserts are available through the entire line of mills. The mill is also offered with a counter-rotating (Contraplex) set of pins for added shear for difficult to mill products. The pharmaceutical version of this work horse has been designed specifically for cGMP compliance from the ground up. Size reduction of soft to medium soft material can be accomplished at rates from 3 to 700 Kg/hr depending on feed material and final size requirements.
Alpine UPZ Ultraplex Fine Impact Mill can also be integrated into Stott Isolators. This arrangement provides a completely integrated system capable of containment levels as low as 1 micro-gram/cubic meter.
Operation of the mill is simple. Material is introduced to the mill via feed device such as a rotary air lock or volumetric/gravimetric feeder through the mill's inlet. The inlet directs the material to the grinding chambers center. The grinding toll rotates at high speed, creating centrifugal force that will accelerate the pharma-powder outwards. The particles outward flow hurls them at high speed against the pins or other grinding media where the impact will cause the particles to fracture.
The wet material is fed through customized feeding systems into the grinding and drying section of the dryer's main body. The grinding rotor disperses the wet material into very fine particles and the fine particles are fluidized in the grinding chamber by temperature-controlled, hot gas coming in from the air heater.
The hot air (or inert gas) can be heated up to 650 °C and as the wet product is dispersed, it is reduced in size in the bottom section of the dryer. The system is kept under a negative pressure by the exhaust fan and the surface area of the product is increased enormously so that water (or other solvents) is evaporated instantaneously.
The dry and fine particles are conveyed with the gas stream to the top section of the dryer where a separator classifies the particles by size. Then the particles pass the classifier at the set cut point and are conveyed with the exhaust air to a powder air separating system like the cyclone, cyclone filter or cyclone scrubbers.
The Micron Dryer flash dryer retains a fluidized bed of product in the drying chamber to ensure a low level of adhesion of wet material on the inside wall of the drying chamber. Moreover, process parameters like classifier speed and outlet temperature can be adapted to control moisture content and particle size of the end product.
Ultra fine regular end product - Due to its specially designed dispersion rotor, our flash dryers are able to produce ultra-fine powders in one step from suspensions, slurries, pastes and dough, filter cakes or wet powders.
High evaporation capacity - Due to the combination of high ?T with a good dispersion of the wet product in the air, our flash dryers can evaporate large quantities of liquids.
Compact design - Compared to other direct drying technologies, the flash dryer requires up to 50% less space.
Multi-purpose - Filter cake or slurry, in the same machine. Therefore with the Drymeister-H unlimited mechanical dewatering is possible previous to the final drying stage.
Easy access - Either for cleaning, inspection or maintenance inside the dryer, our flash dryers offers the best accessibility from the market, regardless which size.
Various systems available - Open, closed- and recycle system concepts.